Esprimo 5615 error 113

[sschindler]

Hallo,

wir haben neuerdings ein Problem bei der Installation von Windows XP auf Esprimo P5615 PCs. Die PCs starten ganz normal mit Boot PXE, laden das OPSI Bootimage und starten das mini Linux. Nach einiger zeit erscheint jedoch die Fehlermeldung “Failed to connect to https://opsiserver:4447/rpc error 113 no route to host“. Wir benutzen opsi linux bootimage version 20090911 und bei anderen PCs (P5625) gibt es diese Probleme nicht. Und noch merkwürdiger ist, dass mit dem vorhergehenden Bootimage die Installation einwandfrei funktionierte.


Hier das Bootlog von einem der betroffenen PCs:
.
.
.
.
[Executing: /sbin/pump -s -i eth0 (Posix.py|290)
->>> Device eth0 (Posix.py|161)
->>> IP: x.x.x.x (Posix.py|161)
->>> Netmask: 255.255.255.0 (Posix.py|161)
->>> Broadcast: x.x.x.255 (Posix.py|161)
->>> Network: x.x.x.0 (Posix.py|161)
->>> Boot server x.x.x.x (Posix.py|161)
->>> Next server x.x.x.x (Posix.py|161)
->>> Gateway: x.x.x.x (Posix.py|161)
->>> Gateways: x.x.x.x (Posix.py|161)
->>> Boot file: /linux/pxelinux.0 (Posix.py|161)
->>> Domain: kevb.lan (Posix.py|161)
->>> Nameservers: x.x.x.x (Posix.py|161)
->>> Ntpservers: x.x.x.x (Posix.py|161)
->>> Renewal time: Fri Mar 12 21:09:10 2010 (Posix.py|161)
->>> Expiration time: Fri Mar 12 22:39:10 2010 (Posix.py|161)
Exit code: 0 (Posix.py|204)
DHCP result for device eth0:
{
"ntpservers" : " x.x.x.x ",
"domain" : "lan",
"network" : " x.x.x.x ",
"nameservers" : " x.x.x.x ",
"ip" : " x.x.x.x ",
"bootfile" : "/linux/pxelinux.0",
"broadcast" : " x.x.x.x ",
"renewaltime" : "Fri",
"netmask" : " x.x.x.x ",
"gateways" : " x.x.x.x ",
"nextserver" : " x.x.x.x ",
"expirationtime" : "Fri",
"bootserver" : " x.x.x.x ",
"gateway" : " x.x.x.x "
} (master.py|256)
Executing: /sbin/ifconfig eth0 (Posix.py|262)
->>> eth0 Link encap:Ethernet HWaddr 00:19:99:2c:57:c1 (Posix.py|161)
->>> inet addr:x.x.x.x Bcast:x.x.x.255 Mask:255.255.255.0 (Posix.py|161)
->>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 (Posix.py|161)
->>> RX packets:8 errors:2 dropped:0 overruns:0 frame:2 (Posix.py|161)
->>> TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 (Posix.py|161)
->>> collisions:0 txqueuelen:1000 (Posix.py|161)
->>> RX bytes:1987 (1.9 KB) TX bytes:2529110 (2.5 MB) (Posix.py|161)
->>> Interrupt:10 Base address:0xe000 (Posix.py|161)
->>> (Posix.py|161)
Exit code: 0 (Posix.py|204)
Current network config: (master.py|287)
device : eth0 (master.py|288)
hardwareAddress : None (master.py|289)
ipaddress : x.x.x.x (master.py|290)
netmask : 255.255.255.0 (master.py|291)
gateway : x.x.x.x (master.py|292)
nameserver : x.x.x.x (master.py|293)
hostname : c-080332 (master.py|294)
domain : kevb.lan (master.py|295)
nextserver : x.x.x.x (master.py|296)
Using FQDN 'c-080332.kevb.lan' (master.py|392)
Creating JSONRPCBackend instance (try #1) (master.py|430)
Failed to get possible methods from backend manager (JSONRPC.py|141)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Executing jsonrpc method 'getPossibleMethods_listOfHashes' (JSONRPC.py|225)
Options: {} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Successfully connected to 'x.x.x.x:4447' (JSONRPC.py|186)
Product-id is 'winxppro' (master.py|490)
Fetching product... (master.py|493)
Executing jsonrpc method 'getProduct_hash' (JSONRPC.py|225)
Options: {'params': ('winxppro', '__UNDEF__')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: , trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Successfully connected to 'x.x.x.x:4447' (JSONRPC.py|186)
Using method POST (JSONRPC.py|283)
Traceback: (Logger.py|648)
line 306 in '__request' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 950 in 'getresponse' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
line 390 in 'begin' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
line 354 in '_read_status' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
==>>> (JSONRPC.py|320)
Product 'winxppro' not found: Request to 'https://x.x.x.x:4447/rpc' failed: (master.py|498)
Fetching product properties... (master.py|502)
Executing jsonrpc method 'getProductProperties_hash' (JSONRPC.py|225)
Options: {'params': ('winxppro', 'c-080332.kevb.lan')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: , trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
No product properties found for productId 'winxppro': Failed to connect to 'https://x.x.x.x:4447/rpc': Timed out after 30 seconds (master.py|507)
Fetching network config... (master.py|523)
Executing jsonrpc method 'getNetworkConfig_hash' (JSONRPC.py|225)
Options: {'params': 'c-080332.kevb.lan'} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: [Errno 113] No route to host, trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Failed to get network config: Failed to connect to 'https://x.x.x.x:4447/rpc': [Errno 113] No route to host (master.py|528)
Fetching general config... (master.py|531)
Executing jsonrpc method 'getGeneralConfig_hash' (JSONRPC.py|225)
Options: {'params': 'c-080332.kevb.lan'} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: [Errno 113] No route to host, trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Failed to get general config: Failed to connect to 'https://x.x.x.x:4447/rpc': [Errno 113] No route to host (master.py|536)
Fetching pcpatch password... (master.py|540)
Executing jsonrpc method 'getPcpatchPassword' (JSONRPC.py|225)
Options: {'params': 'c-080332.kevb.lan'} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: [Errno 113] No route to host, trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Traceback: (Logger.py|648)
line 541 in '<module>' in file '/usr/local/bin/master.py' (Logger.py|648)
line 3 in 'getPcpatchPassword' in file '<string>' (Logger.py|648)
line 251 in '_jsonRPC' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 317 in '__request' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 188 in '_connect' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
==>>> Failed to connect to 'https://x.x.x.x:4447/rpc': [Errno 113] No route to host (master.py|671)
Executing jsonrpc method 'unsetProductActionRequest' (JSONRPC.py|225)
Options: {'params': ('winxppro', 'c-080332.kevb.lan')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Request to 'https://x.x.x.x:4447/rpc' failed: [Errno 113] No route to host, trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Traceback: (Logger.py|648)
line 675 in '<module>' in file '/usr/local/bin/master.py' (Logger.py|648)
line 1 in 'unsetProductActionRequest' in file '<string>' (Logger.py|648)
line 251 in '_jsonRPC' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 317 in '__request' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 188 in '_connect' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
==>>> Failed to connect to 'https://x.x.x.x:4447/rpc': [Errno 113] No route to host (master.py|678)
->>> umount: /mnt/opsi: not found (Posix.py|183)
Cannot umount: Command '/bin/umount /mnt/opsi' failed (1):
umount: /mnt/opsi: not found
(Posix.py|586)

Vorab schonmal Danke für alle Vorschläge!

Gruß

[d.oertel]

Hi,

da der log zeigt, das die Netzwerkverbindung teilweise funktioniert
würde ich erstmal prüfen ob das Problem auch in anderen Umgebungen
(z.B. Knoppix, Winpe) auftaucht.

gruss
d.oertel

[sschindler]

Hallo,

also ich habe den PC mit einer Knoppix CD Problemlos starten können und der Netzwerkzugriff funktioniert auch einwandfrei.
Ich habe zum testen auch mal andere Netboot Produkte angestartet um zu sehen ob diese durchlaufen. Das Programm memtest kann ohne Probleme gestartet werden, aber bei dem Aufruf von wipedisk kommt der Fehler: ==>>> [Errno 112] Host is down: '/mnt/opsi/install/wipedisk/wipedisk.py' (master.py|671)
Scheint mir so als ob es nur Probleme gibt, wenn auf die Festplatte zugegriffen werden muss?!

Das Boot log beim start von Wipedisk:

...
Request to 'https://x.x.x.x:4447/rpc' failed: , trying to reconnect (JSONRPC.py|316)
Opening https connection to x.x.x.x:4447 (JSONRPC.py|172)
Successfully connected to 'x.x.x.x:4447' (JSONRPC.py|186)
Using method POST (JSONRPC.py|283)
Executing jsonrpc method 'setProductInstallationStatus' (JSONRPC.py|225)
Options: {'params': ('wipedisk', 'c-xxxxxx.lan', 'installing')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Executing jsonrpc method 'unsetProductActionRequest' (JSONRPC.py|225)
Options: {'params': ('wipedisk', 'c-xxxxxx.lan')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Traceback: (Logger.py|648)
line 655 in '<module>' in file '/usr/local/bin/master.py' (Logger.py|648)
==>>> [Errno 112] Host is down: '/mnt/opsi/install/wipedisk/wipedisk.py' (master.py|671)
Executing jsonrpc method 'unsetProductActionRequest' (JSONRPC.py|225)
Options: {'params': ('wipedisk', 'c-xxxxx.lan')} (JSONRPC.py|229)
Using method POST (JSONRPC.py|283)
Traceback: (Logger.py|648)
line 306 in '__request' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 950 in 'getresponse' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
line 390 in 'begin' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
line 354 in '_read_status' in file '/usr/lib/python2.6/httplib.py' (Logger.py|648)
==>>> (JSONRPC.py|320)
Traceback: (Logger.py|648)
line 675 in '<module>' in file '/usr/local/bin/master.py' (Logger.py|648)
line 1 in 'unsetProductActionRequest' in file '<string>' (Logger.py|648)
line 251 in '_jsonRPC' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
line 321 in '__request' in file '/var/lib/python-support/python2.6/OPSI/Backend/JSONRPC.py' (Logger.py|648)
==>>> Request to 'https://x.x.x.x:4447/rpc' failed: (master.py|678)
Executing: cat /var/tmp/opsi/sysconf.ini (master.py|688)
->>> [General] (Posix.py|161)
...

edit:
Ein Hardware Inventory bricht mit der selben Fehlermeldung wie die Windowsinstallation ab.

[d.oertel]

Hi,

bitte mal andere bootimage / bootcd -Versionen ausprobieren.

gruss
d.oertel

[wolfbardo]

eventuell helfen auch andere Kernelparameter:

Editieren der Datei /tftpboot/linux/pxelinux.cfg/install
Ändern der Zeile:

Code: Alles auswählen

append noapic lang=de ...

in:

Code: Alles auswählen

append acpi=off noapic lang=de ...

Gruss
Bardo Wolf

[sschindler]

Hallo,

Danke für den Tipp! Die Änderung in /tftpboot/linux/pxelinux.cfg/install haben was gebracht. Nun startet die Installation und kommt bis zur Formatierung der Festplatte. Im Anschluß kann aber auf sda1 nicht zugeriffen werden.

Bootlog:

[6] [Mar 17 15:09:29] Executing: /sbin/sfdisk -l /dev/sda (Posix.py|1301)
[6] [Mar 17 15:09:57] ->>> (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Disk /dev/sda: 9729 cylinders, 255 heads, 63 sectors/track (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Device Boot Start End #cyls #blocks Id System (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda1 * 0+ 9728 9729- 78148161 c W95 FAT32 (LBA) (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda2 0 - 0 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda3 0 - 0 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda4 0 - 0 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] Exit code: 0 (Posix.py|204)
[5] [Mar 17 15:09:57] Size of disk '/dev/sda': 80023749120 Byte / 80023 MB (Posix.py|1326)
[6] [Mar 17 15:09:57] Partition found =>>> number: 1, start: 0 MB (0 cyl), end: 80015 MB (9728 cyl), size: 80023 MB (9729 cyl), type: c, fs: fat32, boot: True (Posix.py|1362)
[6] [Mar 17 15:09:57] Executing: /sbin/sfdisk -uS -l /dev/sda (Posix.py|1365)
[6] [Mar 17 15:09:57] ->>> (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Disk /dev/sda: 9729 cylinders, 255 heads, 63 sectors/track (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Units = sectors of 512 bytes, counting from 0 (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> Device Boot Start End #sectors Id System (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda1 * 63 156296384 156296322 c W95 FAT32 (LBA) (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda2 0 - 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda3 0 - 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] ->>> /dev/sda4 0 - 0 0 Empty (Posix.py|161)
[6] [Mar 17 15:09:57] Exit code: 0 (Posix.py|204)
[6] [Mar 17 15:09:57] Partition sector values =>>> number: 1, start: 63 sec, end: 156296384 sec, size: 156296322 sec (Posix.py|1381)
[5] [Mar 17 15:09:57] Creating filesystem 'fat32' on '/dev/sda1'. (Posix.py|1856)
[6] [Mar 17 15:09:57] Executing: mkfs.vfat -F 32 /dev/sda1 (Posix.py|1875)
[6] [Mar 17 15:09:57] ->>> mkfs.vfat 3.0.1 (23 Nov 2008) (Posix.py|161)
[2] [Mar 17 15:09:57] ->>> /dev/sda1: No such file or directory (Posix.py|183)
[6] [Mar 17 15:09:57] Exit code: 1 (Posix.py|204)
[1] [Mar 17 15:09:58] Traceback: (Logger.py|648)
[1] [Mar 17 15:09:58] line 655 in '<module>' in file '/usr/local/bin/master.py' (Logger.py|648)
[1] [Mar 17 15:09:58] line 54 in '<module>' in file '/mnt/opsi/install/winxppro/setup.py' (Logger.py|648)
[1] [Mar 17 15:09:58] line 1875 in 'createFilesystem' in file '/var/lib/python-support/python2.6/OPSI/System/Posix.py' (Logger.py|648)
[1] [Mar 17 15:09:58] line 208 in 'execute' in file '/var/lib/python-support/python2.6/OPSI/System/Posix.py' (Logger.py|648)
[1] [Mar 17 15:09:58] ==>>> Command 'mkfs.vfat -F 32 /dev/sda1' failed (1):
mkfs.vfat 3.0.1 (23 Nov 2008)
/dev/sda1: No such file or directory
(master.py|671)
[6] [Mar 17 15:09:58] Executing jsonrpc method 'unsetProductActionRequest' (JSONRPC.py|225)
[6] [Mar 17 15:09:58] Options: {'params': ('winxppro', 'c-xxxxx.lan')} (JSONRPC.py|229)
[6] [Mar 17 15:09:58] Using method POST (JSONRPC.py|283)

Hi,

bitte mal andere bootimage / bootcd -Versionen ausprobieren.

gruss
d.oertel

Das Bootimage würde ich nur ungern wechseln, weil wir mit anderen PCs (FSC 5625,5635,Lenovo,Dell) eigentlich keine Probleme haben.

Gruß

sschindler

[d.oertel]

Hi,

sieht seltsam aus.
Ist wohl eher was für einen Supportvertrag.

gruss
d.oertel