Client installation using service_setup.cmd

[barun mukhopadhyay]

Hi

The installer finally run --- but there is an error --- I am enclosing the error log file


1] [2/20/2013 19:26:56] opsi-winst 4.11.3.2 started at >>2/20/2013 19:26:55

[1] [2/20/2013 19:26:56] startmessage opsi-winst created at CentralForm.FormCreate: 2/20/2013 19:26:55

[1] [2/20/2013 19:26:56] startmessage StartProgramModes and create log: 2/20/2013 19:26:55

[1] [2/20/2013 19:26:56]

[1] [2/20/2013 19:26:56] ============ Version 4.11.3.2 WIN32 script "c:\tmp\opsi\setup.ins"

[1] [2/20/2013 19:26:56] start: 2013-02-20 19:26:56

[1] [2/20/2013 19:26:56] on client named "ADSL_IT-PC"

[1] [2/20/2013 19:26:56] loggedin user "Administrator"

[1] [2/20/2013 19:26:56] winst running as "Administrator"

[1] [2/20/2013 19:26:56] winst running with admin privileges

[1] [2/20/2013 19:26:56] winst running in standard script mode

[1] [2/20/2013 19:26:56] [executing: "c:\tmp\opsi\opsi-winst\winst32.exe"]

[1] [2/20/2013 19:26:56] system infos:

[1] [2/20/2013 19:26:56] 40-61-86-33-A6-4C - PC hardware address

[1] [2/20/2013 19:26:56] ADSL_IT-PC - IP name

[1] [2/20/2013 19:26:56] 10.1.10.74 - IP address

[1] [2/20/2013 19:26:56] ENU - System default locale

[1] [2/20/2013 19:26:56] MS Windowds 6.1 32 Bit

[1] [2/20/2013 19:26:56]

[1] [2/20/2013 19:26:56] LogLevel was 6

[1] [2/20/2013 19:26:56] LogLevel set to 7

[1] [2/20/2013 19:26:56] LogLevel was 7

[1] [2/20/2013 19:26:56] LogLevel set to 7

[1] [2/20/2013 19:26:56] LogLevel was 7

[1] [2/20/2013 19:26:56] LogLevel set to 7

[3] [2/20/2013 19:26:56] Error: service not initialized

[3] [2/20/2013 19:26:56] Error: no connection to service

[1] [2/20/2013 19:26:56] LogLevel was 7

[1] [2/20/2013 19:26:56] LogLevel set to 7

[3] [2/20/2013 19:26:59] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Opsi authentication error: Forbidden: Backend authentication error: Backend authentication error: PAM authentication failed for user 'adminuser': ('Authentication failure', 7)","class":"OpsiAuthenticationError"}

[3] [2/20/2013 19:27:01] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Opsi authentication error: Forbidden: Backend authentication error: Backend authentication error: PAM authentication failed for user 'adminuser': ('Authentication failure', 7)","class":"OpsiAuthenticationError"}

[4] [2/20/2013 19:27:01] opsi service version could not retrieved, perhaps no connection

[3] [2/20/2013 19:27:01] Error: no connection to service

[1] [2/20/2013 19:27:01] LogLevel was 7

[1] [2/20/2013 19:27:01] LogLevel set to 7

[1] [2/20/2013 19:27:01] LogLevel was 7

[1] [2/20/2013 19:27:01] LogLevel set to 7

[1] [2/20/2013 19:27:45] LogLevel was 7

[1] [2/20/2013 19:27:45] LogLevel set to 7

[3] [2/20/2013 19:27:46] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Bad hostname: 'adsl_it-pc'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: -> {"message":"Bad hostname: 'adsl_it-pc'","class":"ValueError"}

[1] [2/20/2013 19:27:46] LogLevel was 7

[1] [2/20/2013 19:27:46] LogLevel set to 7

[3] [2/20/2013 19:27:46] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Bad fqdn: 'adsl_it-pc.uib.local'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: -> {"message":"Bad fqdn: 'adsl_it-pc.uib.local'","class":"ValueError"}

[1] [2/20/2013 19:27:46] LogLevel was 7

[1] [2/20/2013 19:27:46] LogLevel set to 7

[1] [2/20/2013 19:27:46] LogLevel was 7

[1] [2/20/2013 19:27:46] LogLevel set to 7

[3] [2/20/2013 19:27:46] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Bad hostname: 'adsl_it-pc'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: -> {"message":"Bad hostname: 'adsl_it-pc'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: retrieveJSONObject --- opsi service problem ----> {"message":"Bad fqdn: 'adsl_it-pc.uib.local'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: -> {"message":"Bad fqdn: 'adsl_it-pc.uib.local'","class":"ValueError"}

[3] [2/20/2013 19:27:46] Error: Could not get hostkey - aborting

[1] [2/20/2013 19:27:53] ___________________

[1] [2/20/2013 19:27:53] script finished

[1] [2/20/2013 19:27:53] 13 errors

[1] [2/20/2013 19:27:53] 1 warning

[1] [2/20/2013 19:27:53]

[1] [2/20/2013 19:27:53]

[1] [2/20/2013 19:27:53] ============ opsi-winst Version 4.11.3.2 WIN32 is regularly exiting. Time 2013-02-20 19:27:53 .


Request , pls help to resolve this error .

regards
barun

Hi Bardo / Ueluekmen

Pls help - now stuck here .

regards

barun

[ueluekmen]

Ok, two problems:

first problem: You don't get a service connection. When the login-mask pops up, you must enter credentials from an opsiadmin not from local machine like Administrator, ...
second problem: You don't use clean FQDN-Names. Underscores in Hostnames are not allowed, because there are not allowed by restriction in the RFC.

You should use your own DNS-Domain, if you have no Domain you can use something like: opsi.local, by the domain is really important that you use a sub-top-leveldomain, for example: opsi.local works but only opsi will not work.
After this you should rename your client: "adsl_it-pc" to "adsl-it-pc". Last but not least run service_setup.cmd on the Client and when the Installation asks you to enter user credentials, enter the usercredentials which you use for the login to opsi-configed.

Then it should work.

[barun mukhopadhyay]

Hello Burdo and Ueluekmer

It is done -- I have changed the name of the pc -- no underscore and it is in the opsi-configed application

thanks a lot

best wishes and regards

barun

[barun mukhopadhyay]

Hello Burdo and Ueluekmer

1 ) I am not able to configure client from the opsi-cofiged . I have selected the option create new opsi-client , input ip =10.1.10.190 for the client ; ip domain name = uib.local ; hardware address = mac address of the new client . The error message is : opsi service error :[Value Error] , bad host name :'10.1.10.190'

2 ) I am trying to install netboot products like hwinvent through opsi-configed , in the right hand side of the window , all the writing are in the German language although I have selected english language from "File----->choose language---->en"

pls help

regards

barun

[barun mukhopadhyay]

[quote="barun mukhopadhyay"]Hello

1 ) I am not able to configure client from the opsi-cofiged . I have selected the option create new opsi-client , input ip =10.1.10.190 for the client ; ip domain name = uib.local ; hardware address = mac address of the new client . The error message is : opsi service error :[Value Error] , bad host name :'10.1.10.190'

2 ) I am trying to install netboot products like hwinvent through opsi-configed , in the right hand side of the window , all the writing are in the German language although I have selected english language from "File----->choose language---->en"

3 ) The log files and the sql database entries :
Pls guide me :
3.1. How to truncate or delete old log files ?
3.2 . log file locations ..
4 ) Is there any way so that , the USB port can be opened / closed for pen drive read/write , USB modem enable / disable ;

These are practical and security requirement

Pls help .

regards

barun

[barun mukhopadhyay]

Hello

I am in need of help -- is there anybody who can help me ...

regards

barun

[d.oertel]

Hi,

the first line in the create client is not the IP ADDRESS but the clients name part of the full qualified DNS Name.
If the client is : 'mybox.mydom.com' so enter 'mybox'

regards

d.oertel

[barun mukhopadhyay]

Hello

Thank you very much .
Is there any way so that , the USB port can be opened / closed for pen drive read/write , USB modem enable / disable ;

best regards

barun

[barun mukhopadhyay]

Hello

There is no AD ; all the clients are in WORKGROUP ; I have tried with the computer name also but not working - shall I have to have an entry in the hosts file in the client mc ...computer name and its ip address

Also , I am selecting the client and trying to shutdown the remote client - the error is : ip is not found out - but the windows client is successfully on the client list tab

What can be the problem ....
To make your opsi 4.0.2 at per with similar remote asset management system , I know what faclities are rewquired from opsi . The USB blocking is absolutely necessary . Also , the software and hardware inventory list -- aggregated over all the clients and not individual client wise .

best regards

barun

[barun mukhopadhyay]

Hello d.oertel

The remote client is created but its hw and sw inventory is not visible ; I have selected the Product configuration option , then selected the lines hwaudit first and then swaudit ; selected requested action and then selected action setup using the left mouse button click - finally saved the new selection ; then rebooted the client but ; but hwaudit and swaudit on the client didnot started automatically .

What to do .....

best regards

barun