Differences

This shows you the differences between two versions of the page.

Link to this comparison view

userspace:check_innosetup-exitcode [2011/10/10 15:46] (current)
Der-Matze created
Line 1: Line 1:
 +====== check_innosetup-exitcode ======
 +Script by Der-Matze \\
 +Comments and improvements welcome \\
  
 +Tested with opsi 4.0.1 \\
 +Tested with opsi-winst 4.10.x - 4.11.1.6 \\
 +Tested with Windows XP Professional and Windows 7 Enterprise x64 \\
 +
 +Subscript that checks all available innosetup exitcodes, writes the definition of the encountered exitcode to the logfile and determines if the installation was successful or not. \\
 +Makes debugging installations easier and assures that failed installations show up as failed in configed. \\
 +
 +Usage: \\
 +
 +<code winst>
 +
 +Winbatch_Install
 +
 + sub "​%ScriptDrive%\install\check_exitcode\check_innosetup-exitcode.ins"​
 +
 +</​code>​
 +
 + 
 +References: http://​unattended.sourceforge.net/​InnoSetup_Switches_ExitCodes.html \\
 +
 +
 +
 +
 +==== check_innosetup-exitcode.ins ====
 +
 +<code winst>
 +
 +;Den ExitCode des Installers abfragen
 + set $ExitCode$ = getLastExitCode
 +
 +
 +
 +;Loglevel anpassen
 + setLogLevel = 4
 +
 +
 +
 +;Den ExitCode auswerten
 +
 +if ($ExitCode$ = "​0"​)
 + setLogLevel = 5
 + comment "​ExitCode = "​+$ExitCode$+"​ Setup was successfully run to completion."​
 + setLogLevel = 4
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​1"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ Setup failed to initialize."​
 + isFatalError
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​2"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ The user clicked Cancel in the wizard before the actual installation started, or chose "​No"​ on the opening "This will install..."​ message box."
 + isFatalError
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​3"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ A fatal error occurred while preparing to move to the next installation phase (for example, from displaying the pre-installation wizard pages to the actual installation process). This should never happen except under the most unusual of circumstances,​ such as running out of memory or Windows resources."​
 + isFatalError
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​4"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ A fatal error occurred during the actual installation process."​
 + isFatalError
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​5"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ The user clicked Cancel during the actual installation process, or chose Abort at an Abort-Retry-Ignore box."
 + isFatalError
 +
 +endif
 +
 +
 +
 +if ($ExitCode$ = "​6"​)
 +
 + setLogLevel = 5
 + logError "​ExitCode = "​+$ExitCode$+"​ The Setup process was forcefully terminated by the debugger (Run | Terminate was used in the IDE)."
 + isFatalError
 +
 +endif
 +
 +
 +
 +;Loglevel anpassen
 + setLogLevel = 6
 +
 +</​code>​

QR Code
QR Code userspace:check_innosetup-exitcode (generated for current page)